As of this writing, I’ve been wearing my new Omnipod 5 pump for about 2 ½ days. I will be changing my first Omnipod 5 pod later this evening, but before then, I wanted to jot down my initial impressions of the system as a whole so far.
The PDM: A bit larger and more brick-like compared to my Dash PDM. Actually, the size is pretty on par with my iPhone. I like that the screen is larger and it seems more sensitive to touch than my Dash – all good things. Except I can’t figure out why it makes chiming sounds only sometimes after I enter my PIN! I’m sure I’ll learn the cause of that eventually…
The pod: Basically indistinguishable from my Dash pods – the only difference I’ve spotted (or rather heard) has to do with the mechanical ticking sound my pod makes when it’s delivering my basal insulin. The old pods had a set frequency, whereas the 5 pods seem to go “tick, tick, tick” in bursts of three or so. Not sure why, but I know I’m still getting my basal rate delivered, which is what counts.
The set-up: Inputting all of my settings into the 5 only took me about 15-20 minutes. It was so easy that it likely would’ve taken me less time if I wasn’t so thorough and careful about triple-checking my settings. I also think it was relatively seamless for me because I was already familiar with 90% of the PDM’s functionality – the only thing I had (and still have to) explore further is automated mode…see below.
Automated vs. manual modes: I can go back and forth between automated (insulin delivery is automatic and the system responds to highs and lows based on data it receives from my Dexcom) and manual (I have to make my own adjustments, just like I did with the older versions of Omnipod). This was a helpful feature for me because I inexplicably got scared of automated mode the first night I wore the pod. I didn’t know what to expect from it – should I trust it right away? Would I notice it working? What if it didn’t? Ultimately, I decided I wasn’t comfortable going to sleep in automated mode, so I kept manual mode on because I wanted to have more control. I waited until the following morning before I turned it on, and since then, I’ve been on automated mode and I’ve spent a solid chunk of my time in range. A few highs here and there, but all my lows seem to be detected before I drop too much, which is just awesome.
Dexcom integration: Similar to the overall set-up of the system, it was extremely easy to get my Dexcom synced up with my Omnipod. All I had to do was enter the 6-character transmitter ID into my PDM and give it a few moments to pick up my Dexcom’s signal. And that was it! I’m sure things will get a little more dicey on days that I have to do both a pod and CGM change (coincidentally, I’m going to do just that in a few hours for the first time…eek), but I do have confidence in my ability to time the changes well so I don’t go without automated mode or Dexcom data for too long.
Let’s talk about sleep: The indisputable best part of this system so far is that I’ve slept soundly the past 3 nights. No CGM alarms going off and waking me up, no frantic shoving of food in my mouth from my bed or late night bolus delivery. And best of all, no waking up in the morning out of range. Now it’s not like that before the 5, I was waking up every night to do something diabetes-related, nor was I starting off each day with a high or low. But I was getting to a point where these things did happen at least on a weekly basis, and naturally, I was getting tired of it. So while I’m acutely aware that I need more time to get to know the system (and it also needs to figure me out), I have hope that it will help me make a major improvement in my diabetes care and management.
All in all, it’s been a relatively smooth start for me and my Omnipod 5. I totally expect some bumps down the road, because that’s normal when starting up any new piece of diabetes technology. But for now, I remain grateful for a comfortable transition to the system.